OUKETECH / OEM CABLE ASSEMBLIES

Custom Coiled Cable Assemblies

OUKETECH brings drawing and BOM review, connector termination, prototype builds, and repeat production to custom coiled cable projects for OEM equipment. We review your connector part numbers and pinout alongside the way the cord moves in the equipment. For a custom coil cord, that means checking the space it occupies at rest, the reach it needs during use, and the load it puts on the connector when pulled. We confirm the coil construction, terminations, and sample acceptance criteria for your design before the build.

Send a drawing, an existing cord, or a sketch showing both mounting points and the required travel. We can use it to identify the dimensions and electrical details needed for a feasibility review. Learn more about our custom cable assembly manufacturing capabilities.

ENGINEERING REVIEW

What we check

01 / Reach

Retracted length and working extension

02 / Fit

Coil diameter, mounting clearance and end exits

03 / Connection

Connector orientation, pinout and strain relief

01 / APPLICATIONS

Choose a coil cord for the job it needs to do

Coiled power cord or coiled power cable

Provide voltage, current, duty cycle, and the plug or equipment connector at each end. If the cable will carry its rated load while partly retracted, include that condition in the review.

Coiled control cable or coiled wire harness

For a handheld controller or movable machine panel, provide the mating interfaces, pin map, and mounting positions. Identify any branch on the harness and whether it sits outside the moving section. See our control cable assembly capabilities.

Shielded coiled cable or coiled data cable

Specify the protocol, pair assignments, shield connections, and any signal checks. For a shielded retractile cable, show where the shield bonds at each end and whether continuity needs to be checked during movement. See our shielded cable assembly capabilities.

02 / DRAWING INPUTS

Specify the coil at rest and in use

A retractable coiled cable can reach a moving part and draw excess cable back when that part returns. To size an industrial coiled cable, sketch both positions with the cable installed. A coil that reaches on a bench can still pull sideways on a connector if the end exits or mounting angles differ on the machine.

Retracted length and working reach

Give both dimensions and identify the measurement points. State whether the straight tails and connectors are included. If there is a separate maximum extension limit, mark it separately from normal working reach.

Coil outside diameter and clearance

Give the maximum outside diameter, the available space around the coil, and any nearby edges or pinch points.

Straight tails and end exits

Specify each tail length, axial or tangential exit, connector orientation, and strain relief. Show the direction the cable pulls at full working reach.

Conductors and pinout

For a 2 core coiled cable, 3 core coiled cable, or 4 core coiled cable, specify conductor size and pin assignments. For a 4 conductor coiled cable, identify any protective earth, drain wire, or shield separately on the drawing.

Motion and environment

State the travel per cycle, frequency, any twist, and expected exposure to heat, oil, cleaning agents, or abrasion. Give a return force limit if the operator or equipment can tolerate only a light pull.

Use our cable assembly drawing requirements to prepare the BOM, connector callouts, and revision information.

03 / SAMPLE APPROVAL

What to verify before releasing a coiled cable assembly

When comparing coiled cable manufacturers, ask how the sample will be evaluated at rest and at working reach. A coil cable manufacturer should be able to tell you which requirements can be verified with a drawing and which need a sample in the actual equipment. Ask your coil cord manufacturer to document the length references and agree on what counts as acceptable recovery after repeated extension.

For an OUKETECH project, agree on visual, dimensional, and pinout or continuity checks against the approved drawing. If the equipment depends on a specific return force, recovery length, or cycle life, define the stroke, mounting orientation, cycle count, and pass criteria for a separate validation. For a data cable, identify any electrical performance that must be checked during motion as well as at rest.

Review the first sample in the intended routing before approving a production build. Confirm the mating fit, connector orientation, tail movement, and coil clearance throughout the stroke. Record the approved drawing revision and the tests required for repeat orders. For company and factory information, see About OUKETECH.

04 / BUYER QUESTIONS

Frequently asked questions

What is a retractile cord?

A retractile cord uses a helical section to extend and draw back as the distance between its ends changes. Supplier catalogs may call these retractile coil cords, and a BOM might describe the same part as a retractable coil cable or retractable coil cord. If the drawing says only “coiled electrical cable,” add the working travel and end orientation to make the requirement clear.

Can you quote from an existing spiral cable assembly?

Yes. A sample can help identify geometry and connectors. Also provide the equipment interface, working reach, electrical requirements, and any failure you want to address. A worn coil may have taken a permanent set, so provide the original retracted length if it is available.

What should I ask a retractile cord manufacturer about cycle life?

Ask how far the cord traveled on each cycle, how the ends were held, whether it carried a load, and what qualified as failure. A cycle count is most useful when the test conditions and acceptance criteria reflect the application.

05 / REQUEST FOR QUOTE

Request a quote for a custom coiled cable

Share the drawing or sample reference, BOM, connector part numbers, pinout, coil dimensions, sample quantity, estimated production quantity, delivery destination, and any acceptance tests. If the design is still open, start with the mounting positions, working travel, and an equipment photo or sketch. Those inputs help establish whether a sample can be built and what needs to be confirmed before quoting production.

Send Your Inquiry Today